Provide internal connection terminals to transmit 24V power supply and communication signal.
![delta dtc 1000 manual delta dtc 1000 manual](https://deltaacdrives.com/wp-content/uploads/DTB9696CRE-Temperature-Controller-Delta-AC-Drives-Diagram.jpg)
Alarm Function Communication Communication Protocol Internal Connection Vibration Resistance Shock Resistance Ambient o C to +5 o C Temperature Storage -2 o C to +65 o C Temperature Altitude 2m or less Relative Humidity 35% to 85% RH (non-condensing) Pollution Degree Degree 2 Mod-bus communication protocol, support RTU/ASCII. 5Ω) Analog voltage output: ~1V (Load resistance shall be higher than 1Ω) Control output, Alarm output, or Retransmission output (only for linear voltage and current output as 1 st group) 12 Alarm mode selections RS-485 digital communication, 24bps~384bps. output current 4mA Current output: DC 4 ~ 2m A output (Load resistance: Max. load 25VAC, 3A resistive load Voltage pulse output: DC 12V, Max.
DELTA DTC 1000 MANUAL MANUAL
PID, PID program control, Manual or / Relay output (SPST), Max. 7 consumption connected) Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Sensor Type Platinum RTD: Pt1, JPt1 Linear DC input: ~5V,~1V, ~ 2 m A,4~2 m A, ~5mV Sampling Rate Control Method Output Type Output Function Analog input.15 sec. Isolated switching power Voltage Range Rated voltage: 9%~11% Power Rated 24 Vdc, Max. 3 FUNCTI AND SPECIFICATI Power Supply DC24V. 5 Main Output R: Relay output SPST, 25VAC, 3A Type V: Voltage Pulse output 12V +1 % ~-2 % C: Current output 4~2mA L: Linear Voltage output ~1V Standard: DC24V input, Relay output for 2 nd group, RS-485 communication.
DELTA DTC 1000 MANUAL SERIES
2 MODEL NAME EXPLANATI DTC DTC Series 1 Controller Position DTC: Delta C series Temperature Controller 1: first controller 2: controller in parallel 1Ģ 2 Auxiliary Output Groups : standard, 2 groups output, no auxiliary output 1: 1 group auxiliary output. For temperature accuracy, keep the controller away from heating source. Do NOT touch internal terminals no matter power on or off. Wait at least one minute after power off to allow capacitors to discharge, and do not touch any internal circuit within this period. Do NOT touch the terminals or repair the controller when power on to prevent electric shock. Make sure power cables and signals device are installed properly before power on otherwise serious damage may occur. Shorten the wire when wiring a platinum resistance thermometer (RTD) to the controller and separate power cable from load wires to prevent interference and conductive influence. Be sure to use compensating wires that match the thermocouple types when extending or connecting the thermocouple wires. Power off when wiring and changing an input sensor.
DELTA DTC 1000 MANUAL INSTALL
Do not install and/or use the controller in places subject to: (a) Dust or corrosive gases and liquid. Do NOT modify or disassemble the controller. Prevent dust or metallic debris from falling into the controller that will cause malfunction. Also, it is equipped with protective methods such as some special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module. Please Install within a separate UL Listed enclosure only, keep the enclosure away from airbome dust or high humidity and prevent electric shock or sudden shock. They are intended for installation completely within an overall panel or Process control Enclosure and are used in heating or cooling applications. These devices are microprocessor-based temperature regulating controllers which may be provide with normally closed and/or open contacts. 1 Precaution DANGER: ELECTRIC SHOCK! DTC1 is an OPEN-TYPE Process Control Equipment and DTC2 is an OPEN-TYPE Process Control Accessory. Please read this instruction sheet before using your C series to ensure proper operation and please keep this instruction sheet handy for quick reference. 1 DTC1/2 Temperature Controller User Manual Thank you very much for purchasing DELTA C Series Temperature Controller.